Good technical condition of your car- very important

se, as in the case of practical lessons on learning to drive car, also in this case we are dealing with the introduction of the student in handling motorcycle. More problems may occur already during city driving, at a later stage

Dodane: 02-09-2016 15:28
Good technical condition of your car- very important reduce smoke Daewoo

Driving a motorcycle - not so simple

At least at the beginning of steering a motorcycle can give lessons to the student serving a practical course driving a lot of problems. Of course, as in the case of practical lessons on learning to drive car, also in this case we are dealing with the introduction of the student in handling motorcycle. More problems may occur already during city driving, at a later stage of practical lessons. This is due to the fact that the instructor and student are in different vehicles, usually a motorcyclist driving instructor in the car. Issuing commands and paying attention to mistakes so it can reach out to the student with some delay and it is the source of many problems.


History of car

The first working steam-powered vehicle was designed?and most likely built?by Ferdinand Verbiest, a Flemish member of a Jesuit mission in China around 1672. It was a 65-cm-long scale-model toy for the Chinese Emperor that was unable to carry a driver or a passenger.72122 It is not known if Verbiest's model was ever built.22


Cugnot's 1771 fardier ? vapeur, as preserved at the Musée des Arts et Métiers, Paris
Nicolas-Joseph Cugnot is widely credited with building the first full-scale, self-propelled mechanical vehicle or car in about 1769; he created a steam-powered tricycle.23 He also constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts.24 His inventions were, however, handicapped by problems with water supply and maintaining steam pressure.24 In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam-powered road vehicle. It was unable to maintain sufficient steam pressure for long periods, and was of little practical use.

The development of external combustion engines is detailed as part of the history of the car, but often treated separately from the development of true cars. A variety of steam-powered road vehicles were used during the first part of the 19th century, including steam cars, steam buses, phaetons, and steam rollers. Sentiment against them led to the Locomotive Acts of 1865.

Źródło: https://en.wikipedia.org/wiki/Car#History


In engines with more than one cylinder

The base of a reciprocating internal combustion engine is the engine block, which is typically made of cast iron or aluminium. The engine block contains the cylinders. In engines with more than one cylinder they are usually arranged either in 1 row (straight engine) or 2 rows (boxer engine or V engine); 3 rows are occasionally used (W engine) in contemporary engines, and other engine configurations are possible and have been used. Single cylinder engines are common for motorcycles and in small engines of machinery. Water-cooled engines contain passages in the engine block where cooling fluid circulates (the water jacket). Some small engines are air-cooled, and instead of having a water jacket the cylinder block has fins protruding away from it to cool by directly transferring heat to the air. The cylinder walls are usually finished by honing to obtain a cross hatch, which is better able to retain the oil. A too rough surface would quickly harm the engine by excessive wear on the piston.

The pistons are short cylindrical parts which seal one end of the cylinder from the high pressure of the compressed air and combustion products and slide continuously within it while the engine is in operation. The top wall of the piston is termed its crown and is typically flat or concave. Some two-stroke engines use pistons with a deflector head. Pistons are open at the bottom and hollow except for an integral reinforcement structure (the piston web). When an engine is working the gas pressure in the combustion chamber exerts a force on the piston crown which is transferred through its web to a gudgeon pin. Each piston has rings fitted around its circumference that mostly prevent the gases from leaking into the crankcase or the oil into the combustion chamber. A ventilation system drives the small amount of gas that escape past the pistons during normal operation (the blow-by gases) out of the crankcase so that it does not accumulate contaminating the oil and creating corrosion. In two-stroke gasoline engines the crankcase is part of the air?fuel path and due to the continuous flow of it they do not need a separate crankcase ventilation system.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine